Just about everyone is bound to have their own individual rationale when it comes to How to Install a Bathtub Yourself.
Installing a bathtub isn't precisely brain surgery, yet it does need strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably tough project. If the old bathtub is readily accessible, the job can relocate rapidly; if you have to open a wall surface to get rid of the old tub as well as position the brand-new tub, the job is a lot harder. In either situation, the task is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the brand-new one. Ensure you have certified yourself for the task and are comfortable trying it. Rather than hiring a specialist to take over a halfway-completed job, it is much better to think about utilizing one before you start. Chances are you may need an expert plumber to make tube connections.
This post will aid you set up a new bath tub in your bathroom if you have actually currently bought a brand-new tub and don't require to change the plan of your previous water supply pipelines.
Your devices and material list should comprise the following:
Preparing for the Installment
First of all, the sustaining framework provided with the bathroom should be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets system to stop stress on the bath tub.
Fit the flexible faucet ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its final position.
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly troublesome due to the restricted accessibility that is usually the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the staying water that will come from the pipes. As soon as the supply pipelines have actually been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning throughout this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
Before moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Making use of both wooden boards under its feet, position the tub in the required placement. The wooden boards are valuable in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four little points.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the level and also changing the feet on the bath tub till the level reads level.
To set up faucets, fit all-time low of the outermost flexible tap port to the proper supply pipeline by making a compression join; after that do the exact same for the other tap.
Turn on the water and also examine all joints as well as brand-new pipework for leaks and tighten them if needed. Fill up the tub as well as likewise inspect the overflow electrical outlet as well as the normal electrical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bath tub needs to wait until the bathtub has actually been used a minimum of when as this will certainly resolve it right into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washers are in area between the faucet as well as the sink. Secure the faucet in place with the maker given backnut. When the tap is safely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous type must be connected to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom satisfies the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to split an inflexible seal, creating the water to pass through the wall between the bath and the tiling, resulting in problems with moisture and possible leaks to the ceiling below.
You can pick from a range of coloured sealants to blend in your components and also fittings. They are offered in tubes as well as cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to allow for the movement experienced when the bathtub is in use. The sealer can fracture rather very early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily available on the marketplace. It is a good idea to fit the tiles using water-resistant or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very interested by Installing A Bathtub and I'm hoping you appreciated our page. Sharing is caring. You just don't know, you will be doing someone a favor. Thanks a lot for your time spent reading it.
Urgent plumbing needs? Seek professionals.